UPS & Generator Monitoring
Bài toán
Standby power is only tested monthly, and a UPS on bypass or a generator with low fuel is discovered when the mains fails.
Tổng quan giải pháp
MILESGO gateways collect data from UPS units, generator controllers, automatic transfer switches (ATS), level sensors over SNMP / Modbus RTU / Modbus TCP, and deliver it to the BMS, the NMS (SNMP manager), SMS, email and messaging alarms as BACnet/IP / MQTT / SNMP. Field equipment keeps its own protocol and control logic; integration is done by configuration and point mapping, not custom code.
Typical scope
- UPS units
- generator controllers
- automatic transfer switches (ATS)
- level sensors
Protocol path
SNMP / Modbus RTU / Modbus TCP → BACnet/IP / MQTT / SNMP
Implementation checklist for the project manager
- Collect MIB files, SNMP versions and v3 credentials for every UPS / PDU / cooling model.
- Collect register maps and protocol documents from every equipment vendor early; a missing map is the most common delay.
- Define an alarm matrix (priority, recipient, escalation) and test every alarm end to end at SAT.
- Confirm DIN-rail space and a stable 12–24 V supply in each panel; use UPS-backed power for critical monitoring.
- Commission in read-only mode first; enable write / control points only after the client approves each one.
- Hand over configuration backups, point table, IP plan and as-built drawings, with a short operator training.
Project deliverables
- Signed point table and protocol mapping
- Gateway configuration files and backups
- IP address plan and network drawing
- FAT and SAT test records
- As-built documentation and operator training
Kiến trúc hệ thống
Field layer: UPS units, generator controllers, automatic transfer switches (ATS), level sensors, connected over SNMP / Modbus RTU / Modbus TCP. Edge and integration layer: MILESGO protocol gateways and edge controllers, mounted on DIN rail in existing panels, polling each device, time-stamping values and buffering them locally. Upper layer: the BMS, the NMS (SNMP manager), SMS, email and messaging alarms, which receives the data as BACnet/IP / MQTT / SNMP. Remote access for maintenance runs over VPN rather than open internet ports.
Thành phần hệ thống
- Field devices
- UPS units, generator controllers, automatic transfer switches (ATS), level sensors
- Edge / integration
- MILESGO protocol gateways and edge controllers
- Upper systems
- the BMS, the NMS (SNMP manager), SMS, email and messaging alarms (BACnet/IP / MQTT / SNMP)
- Tools and commissioning
- Web-based configuration, point table import/export (Excel), off-site simulation and on-site diagnostic tools
Năng lực phần mềm và AI
- Predictive maintenance indicators from equipment trendsTrong lộ trình
Các bước triển khai
- 1
Site survey and point list
Inventory devices, protocols, register maps, panel space, power and network paths.
- 2
Design and point table sign-off
Map every point to the target protocol and system; agree it with the client and the upper-system contractor.
- 3
Configuration and FAT
Build the gateway configuration off site, simulate it and test against the signed point table.
- 4
Installation and wiring
Mount gateways on DIN rail, wire RS-485 / I/O / Ethernet, apply the IP plan.
- 5
SAT and alarm tests
Verify values against local readings, test every alarm and command end to end.
- 6
Handover and support
Hand over configuration backups, point table and as-built documents; train operators.
Giá trị cho khách hàng
- Alarms reach the right person by SMS, email or messaging apps
- Abnormal conditions seen early, before they become failures
- One view of all subsystems instead of separate vendor consoles
- Timestamped records for compliance and reporting
Các giải pháp khác trong Energy & Power
Hãy cho chúng tôi biết về dự án của bạn
Gửi giao thức, số điểm dữ liệu và hệ thống đích. Một nhóm kinh doanh và kỹ thuật sẽ xem xét mọi yêu cầu.
Trao đổi về dự án