Generator & ATS Monitoring

المشكلة

Generator controllers and transfer switches are checked on weekly walk-rounds, so a failed start, a switch stuck on one source or low fuel is found too late.

نظرة عامة على الحل

MILESGO gateways collect data from generator controllers, automatic transfer switches (ATS), level sensors, run/stop and fault dry contacts over Modbus RTU / Modbus TCP, and deliver it to the DCIM, the BMS, SMS, email and messaging alarms as SNMP / BACnet/IP / MQTT. Field equipment keeps its own protocol and control logic; integration is done by configuration and point mapping, not custom code.

Typical scope

generator controllers
automatic transfer switches (ATS)
level sensors
run/stop and fault dry contacts

Protocol path

Modbus RTU / Modbus TCP → SNMP / BACnet/IP / MQTT

Implementation checklist for the project manager

Collect register maps and protocol documents from every equipment vendor early; a missing map is the most common delay.
For hard-wired signals, list each DI/DO/AI/AO with its type (dry contact, 4–20 mA, 0–10 V, PT1000) and choose I/O modules accordingly.
Commission in read-only mode first; enable write / control points only after the client approves each one.
Define an alarm matrix (priority, recipient, escalation) and test every alarm end to end at SAT.
Confirm DIN-rail space and a stable 12–24 V supply in each panel; use UPS-backed power for critical monitoring.
Check 4G signal and the SIM data plan at every site before committing to cellular backhaul.

Project deliverables

Signed point table and protocol mapping
Gateway configuration files and backups
IP address plan and network drawing
FAT and SAT test records
As-built documentation and operator training

بنية النظام

Field layer: generator controllers, automatic transfer switches (ATS), level sensors, run/stop and fault dry contacts, connected over Modbus RTU / Modbus TCP. Edge and integration layer: MILESGO protocol gateways and edge controllers, mounted on DIN rail in existing panels, polling each device, time-stamping values and buffering them locally. Upper layer: the DCIM, the BMS, SMS, email and messaging alarms, which receives the data as SNMP / BACnet/IP / MQTT. Remote access for maintenance runs over VPN rather than open internet ports.

مكونات النظام

Field devices: generator controllers, automatic transfer switches (ATS), level sensors, run/stop and fault dry contacts
Edge / integration: MILESGO protocol gateways and edge controllers
Upper systems: the DCIM, the BMS, SMS, email and messaging alarms (SNMP / BACnet/IP / MQTT)
Tools and commissioning: Web-based configuration, point table import/export (Excel), off-site simulation and on-site diagnostic tools

قدرات البرمجيات والذكاء الاصطناعي

Predictive maintenance indicators from equipment trendsضمن الخطة

خطوات التسليم

1
Site survey and point list
Inventory devices, protocols, register maps, panel space, power and network paths.
2
Design and point table sign-off
Map every point to the target protocol and system; agree it with the client and the upper-system contractor.
3
Configuration and FAT
Build the gateway configuration off site, simulate it and test against the signed point table.
4
Installation and wiring
Mount gateways on DIN rail, wire RS-485 / I/O / Ethernet, apply the IP plan.
5
SAT and alarm tests
Verify values against local readings, test every alarm and command end to end.
6
Handover and support
Hand over configuration backups, point table and as-built documents; train operators.

القيمة للعميل

Alarms reach the right person by SMS, email or messaging apps
Abnormal conditions seen early, before they become failures
Timestamped records for compliance and reporting
Monitoring added without changing existing control programs

أخبرنا عن مشروعك

أرسل البروتوكولات وعدد النقاط والنظام المستهدف. يراجع فريق من المبيعات والهندسة كل طلب.

ناقش مشروعك